ZMQ::SOCKET_PAIR-
Exclusive pair pattern
ZMQ::SOCKET_PUB-
Publisher socket
ZMQ::SOCKET_SUB-
Subscriber socket
ZMQ::SOCKET_REQ-
Request socket
ZMQ::SOCKET_REP-
Reply socket
ZMQ::SOCKET_XREQ-
Alias for SOCKET_DEALER
ZMQ::SOCKET_XREP-
Alias for SOCKET_ROUTER
ZMQ::SOCKET_PUSH-
Pipeline upstream push socket
ZMQ::SOCKET_PULL-
Pipeline downstream pull socket
ZMQ::SOCKET_ROUTER-
Extended REP socket that can route replies to requesters
ZMQ::SOCKET_DEALER-
Extended REQ socket that load balances to all connected peers
ZMQ::SOCKET_XPUB-
Similar to SOCKET_PUB, except you can receive subscriptions as messages.
The subscription message is 0 (unsubscribe) or 1 (subscribe) followed by the topic.
ZMQ::SOCKET_XSUB-
Similar to SOCKET_SUB, except you can send subscriptions as messages. See SOCKET_XPUB for format.
ZMQ::SOCKET_STREAM-
Used to send and receive TCP data from a non-ØMQ peer. Available if compiled against ZeroMQ 4.x or higher (Value: integer).
ZMQ::SOCKOPT_HWM-
The high water mark for inbound and outbound messages is a hard limit on the maximum number of outstanding messages ØMQ shall queue in memory for any single peer that the specified socket is communicating with. Setting this option on a socket will only affect connections made after the option has been set. On ZeroMQ 3.x this is a wrapper for setting both SNDHWM and RCVHWM. (Value: integer).
ZMQ::SOCKOPT_SNDHWM-
The ZMQ_SNDHWM option shall set the high water mark for outbound messages on the specified socket. Available if compiled against ZeroMQ 3.x or higher (Value: integer).
ZMQ::SOCKOPT_RCVHWM-
The ZMQ_SNDHWM option shall set the high water mark for inbound messages on the specified socket. Available if compiled against ZeroMQ 3.x or higher (Value: integer).
ZMQ::SOCKOPT_AFFINITY-
Set I/O thread affinity (Value: integer)
ZMQ::SOCKOPT_IDENTITY-
Set socket identity (Value: string)
ZMQ::SOCKOPT_SUBSCRIBE-
Establish message filter. Valid for subscriber socket (Value: string)
ZMQ::SOCKOPT_UNSUBSCRIBE-
Remove message filter. Valid for subscriber socket (Value: string)
ZMQ::SOCKOPT_RATE-
Set rate for multicast sockets (pgm) (Value: integer >= 0)
ZMQ::SOCKOPT_RECOVERY_IVL-
Set multicast recovery interval (Value: integer >= 0)
ZMQ::SOCKOPT_RECONNECT_IVL-
Set the initial reconnection interval (Value: integer >= 0)
ZMQ::SOCKOPT_RECONNECT_IVL_MAX-
Set the max reconnection interval (Value: integer >= 0)
ZMQ::SOCKOPT_MCAST_LOOP-
Control multicast loopback (Value: integer >= 0)
ZMQ::SOCKOPT_SNDBUF-
Set kernel transmit buffer size (Value: integer >= 0)
ZMQ::SOCKOPT_RCVBUF-
Set kernel receive buffer size (Value: integer >= 0)
ZMQ::SOCKOPT_RCVMORE-
Receive multi-part messages (Value: integer)
ZMQ::SOCKOPT_TYPE-
Get the socket type. Valid for getSockOpt (Value: integer)
ZMQ::SOCKOPT_LINGER-
The linger value of the socket. Specifies how long the socket blocks
trying flush messages after it has been closed (Value: integer)
ZMQ::SOCKOPT_BACKLOG-
The SOCKOPT_BACKLOG option shall set the maximum length of the queue of outstanding peer connections for the specified socket; this only applies to connection-oriented transports. (Value: integer)
ZMQ::SOCKOPT_MAXMSGSIZE-
Limits the maximum size of the inbound message. Value -1 means no limit. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::SOCKOPT_SNDTIMEO-
Sets the timeout for send operation on the socket. Value -1 means no limit. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::SOCKOPT_RCVTIMEO-
Sets the timeout for receive operation on the socket. Value -1 means no limit. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::SOCKOPT_IPV4ONLY-
Disable IPV6 support if 1. Available if compiled against ZeroMQ 3.x (Value: integer)
ZMQ::SOCKOPT_LAST_ENDPOINT-
Retrieve the last connected endpoint - for use with * wildcard ports. Available if compiled against ZeroMQ 3.x or higher (Value: string)
ZMQ::SOCKOPT_TCP_KEEPALIVE_IDLE-
Idle time for TCP keepalive. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::SOCKOPT_TCP_KEEPALIVE_CNT-
Count time for TCP keepalive. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::SOCKOPT_TCP_KEEPALIVE_INTVL-
Interval for TCP keepalive. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::SOCKOPT_DELAY_ATTACH_ON_CONNECT-
Set a CIDR string to match against incoming TCP connections. Available if compiled against ZeroMQ 3.x or higher (Value: string)
ZMQ::SOCKOPT_TCP_ACCEPT_FILTER-
Set a CIDR string to match against incoming TCP connections. Available if compiled against ZeroMQ 3.x or higher (Value: string)
ZMQ::SOCKOPT_XPUB_VERBOSE-
Set the XPUB to receive an application message on each instance of a subscription. Available if compiled against ZeroMQ 3.x or higher (Value: string)
ZMQ::SOCKOPT_ROUTER_RAW-
Sets the raw mode on the ROUTER, when set to 1. In raw mode when using tcp:// transport the socket will read and write without ZeroMQ framing.
Available if compiled against ZeroMQ 4.0 or higher (Value: string)
ZMQ::SOCKOPT_IPV6-
Enable IPV6. Available if compiled against ZeroMQ 4.0 or higher (Value: string)
ZMQ::CTXOPT_MAX_SOCKETS-
The socket limit for this context. Available if compiled against ZeroMQ 3.x or higher (Value: integer)
ZMQ::POLL_IN-
Poll for incoming data
ZMQ::POLL_OUT-
Poll for outgoing data
ZMQ::MODE_NOBLOCK-
Non-blocking operation. Deprecated, use ZMQ::MODE_DONTWAIT instead
ZMQ::MODE_DONTWAIT-
Non-blocking operation
ZMQ::MODE_SNDMORE-
Send multi-part message
ZMQ::DEVICE_FORWARDER-
Forwarder device
ZMQ::DEVICE_QUEUE-
Queue device
ZMQ::DEVICE_STREAMER-
Streamer device
ZMQ::ERR_INTERNAL-
ZMQ extension internal error
ZMQ::ERR_EAGAIN-
Implies that the operation would block when ZMQ::MODE_DONTWAIT is used
ZMQ::ERR_ENOTSUP-
The operation is not supported by the socket type
ZMQ::ERR_EFSM-
The operation can not be executed because the socket is not in correct state
ZMQ::ERR_ETERM-
The context has been terminated